A Step-by-Step Overview to Setting Up a Bathtub
A Step-by-Step Overview to Setting Up a Bathtub
Blog Article
Presented here down the page you might get a lot of superb advice around A Step-by-Step Guide to Installing a Bathtub.
Mounting a bath tub isn't exactly rocket science, yet it does need strong plumbing, carpentry, as well as sometimes, tiling skills. Changing an old bathtub with a new one is additionally a moderately tough task. If the old tub is conveniently accessible, the project can relocate speedily; if you have to open up a wall to eliminate the old bathtub and position the brand-new bath tub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will need an assistant to vacate the old tub as well as embeded in the brand-new one. Ensure you have qualified on your own for the job and are comfortable trying it. Rather than hiring a specialist to take control of a halfway-completed project, it is better to think about utilizing one prior to you start. Chances are you may need an expert plumber to make tube links.
This write-up will certainly help you install a new tub in your shower room if you have actually currently acquired a new tub as well as don't need to alter the plan of your previous water pipelines.
Your devices and also product checklist should comprise the following:
Planning for the Installment
To start with, the sustaining frame supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to make sure that if the tap comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the taps system to avoid strain on the bathtub.
Fit the flexible tap adapters to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to now be ready to be suited its last setting.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installation, then the first thing you need to do is separate the water system. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of getting rid of the existing taps can be quite bothersome because of the restricted access that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the taps. Have a cloth all set for the staying water that will originate from the pipelines. When the supply pipes have actually been eliminated, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from transforming during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned of any kind of old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.
Installing the Bath tub
Making use of the two wooden boards under its feet, position the tub in the required placement. The wooden boards are useful in uniformly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto 4 small factors.
The next objective is to ensure that the tub is leveled all round. This can be achieved by inspecting the level and readjusting the feet on the tub until the level reads degree.
To install faucets, fit the bottom of the outermost versatile faucet port to the appropriate supply pipe by making a compression sign up with; then do the same for the other faucet.
Turn on the water supply as well as check all joints as well as new pipework for leakages and tighten them if required. Fill up the bath tub and likewise inspect the overflow electrical outlet and the normal outlet for leakages.
Ultimately, fix the bath paneling as described in the producer's user's manual. Tiling and also securing around the bathtub ought to wait up until the tub has actually been made use of at least once as this will settle it right into its last placement.
Suitable New Touches
If the tails of the new taps are plastic, then you will need a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end provides a connection to the existing supply pipes.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the tap in the placing hole in the bath/basin guaranteeing that the washers remain in location in between the faucet and also the sink. Secure the tap in place with the producer supplied backnut. When the faucet is safely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap adapters. The previous kind must be linked to the tap ends first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the location where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to fracture a rigid seal, causing the water to penetrate the wall between the bathroom as well as the tiling, resulting in problems with dampness and possible leakages to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your fixtures and installations. They are marketed in tubes as well as cartridges, as well as are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with spins of drenched newspaper or soft rope. Remember to always load the bath tub with water before sealing, to allow for the activity experienced when the bathtub is in use. The sealer can split relatively early if you do not take into account this activity prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally quickly available on the marketplace. It is a good idea to fit the tiles using waterproof or water resistant adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you liked our section on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Many thanks for taking the time to browse our blog. Loved our entry? Please share it. Help somebody else check it out. We enjoy reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Booking
Report this page